Kreative Gardens LLC, License # 1137272

Project:

Backyard Artificial Turf, Putting Green & DG Parking

Prepared:

August 9, 2026

Quote Summary

This proposal is for a coordinated backyard landscape improvement for Atreva Richy in Victorville. The project combines premium landscape artificial grass, a small recreational putting green, a dedicated grill pad, decorative gravel and paver improvements, a stabilized decomposed-granite parking area, and a finished treatment along the lower portion of the right-side fence.

The work is designed as one combined project so that excavation, material deliveries, equipment, labor, grading, base preparation, haul-away, and finish work can be coordinated efficiently across the backyard. The areas and quantities shown are approximate and will be field verified before final material placement and cutting.

Artificial Turf Areas

The landscape-turf installation is divided into two primary areas. The main area in front of the covered patio, including the landscape-turf fringe surrounding the putting green, is approximately 571 square feet. A separate turf area surrounding the new grill pad is approximately 153 square feet. The combined estimated Maya 80 landscape-turf coverage is therefore approximately 724 square feet.

The selected landscape turf is Maya 80. Kreative Gardens will perform the standard preparation required for a proper installation, including removal of existing rock and unsuitable surface material within the approved turf areas, excavation as required to establish finished elevations, grading, placement of commercial-grade weed-barrier fabric, installation of recycled Class II road base, mechanical compaction, final grading, turf layout, cutting and fitting, seaming where required, perimeter fastening, infill application, power brushing, and final cleanup.

Maya 80 will also be used as the fringe around the putting green so the recreational green transitions naturally into the surrounding lawn. Final seam locations, grain direction, curves, and field cuts may be adjusted to improve appearance, drainage, material efficiency, and the transition to the existing concrete and new hardscape elements.

Two-Hole Putting Green

Within the main landscape area, Kreative Gardens will construct a compact recreational putting green. The actual putting surface is approximately 105 square feet, while the overall putting-green zone, including the surrounding Maya 80 fringe, is approximately 218 square feet.

The putting surface will use dedicated putting-green artificial grass and will be prepared as a simple, generally flat recreational green without built-up contours or intentionally shaped breaks. The installation includes two complete cup, pole, and flag sets. Final cup placement and minor edge shaping will be determined in the field for practical spacing, clean appearance, and efficient use of the available approximately 9-foot-wide area.

Grill Pad and Surrounding Turf

Next to the covered patio, Kreative Gardens will create a dedicated grill location using nine new 24-inch by 24-inch pavers, supplied and installed as part of this proposal. The pavers will create a stable non-turf surface for the grill so the grill does not need to sit on the covered patio or directly on the artificial grass.

The approximately 153-square-foot surrounding area will be finished with Maya 80 artificial turf. The turf will be carefully cut and fitted around the individual pavers for a clean integrated appearance.

Rear Paver Line and Gray Gravel

Along the rear portion of the yard, the existing paver arrangement will be modified to create the cleaner single-row layout shown in the approved concept sketch. Kreative Gardens will provide the new pavers required for this extension rather than reusing the existing units designated for replacement.

Existing white decorative rock within the designated improvement areas will be removed as required and replaced with 3/4-inch gray gravel, selected to coordinate with the gray gravel already present elsewhere in the yard. The work is intended to create a more cohesive transition between the pool area, new turf, pavers, and remaining landscape surfaces while reducing loose light-colored rock adjacent to the pool.

Black/Gray Paver Edging

Selected existing red edging brick within the redesigned landscape area will be removed and replaced with black or gray concrete paver edging stones similar to the style reviewed with Atreva. These units will create a darker, cleaner boundary that coordinates with the gray gravel, Maya 80 turf, and putting-green area.

Stabilized DG Parking Area

The approximately 300-square-foot parking area at the upper-left portion of the backyard will be constructed as a stabilized decomposed-granite surface intended for residential parking use. Kreative Gardens will prepare the area, install recycled Class II road base, grade and mechanically compact the foundation, and then install approximately 2 to 2-1/2 inches of gray decomposed granite.

The DG will be treated with approximately 20 gallons of TerraKoat EX, a stabilizer selected for driveway and parking applications, and will be compacted to produce a firmer, more erosion-resistant finished surface than ordinary loose landscape DG. The long-term performance of any DG parking surface still depends on proper drainage, subgrade stability, vehicle type, tire movement, weather, and normal maintenance.

Right-Side Fence Bottom Treatment

Along the right-side property fence, where erosion and the exposed lower edge have created an unfinished appearance, Kreative Gardens will install 2-inch by 12-inch pressure-treated lumber along the bottom of the fence. The lumber will receive a brown finish and will be secured with approximately 18-inch steel stakes to create a cleaner visual barrier at ground level.

This treatment is intended as a landscape finish and soil/visual barrier. It is not a structural fence repair, retaining wall, engineered erosion-control system, or replacement of the existing fence.

Access and Existing Lawn Protection

Backyard access is generally suitable for the planned work. Because the equipment access route passes near existing natural grass outside the backyard gate, Kreative Gardens will use reasonable temporary ground-protection methods when moving compact equipment and materials through the access area. Some temporary flattening, discoloration, or minor disturbance of natural grass can occur when construction equipment must cross or work immediately adjacent to a lawn.

Project Pricing

The standard combined-project price for credit-card payment or financing is $11,100. A discounted $10,100 cash price is available. Financing is available for qualified customers.

These prices are based on completing the described work as one coordinated package. The individual project-area values shown on the quote are allocations within the combined project and are not guaranteed stand-alone prices or automatic deduction amounts. If Atreva removes, adds, or materially changes any portion of the scope, Kreative Gardens will recalculate the project price based on the revised materials, labor, deliveries, mobilization, equipment, disposal, and shared project costs.

Grass Model Specifications

Selected Model

Maya 80

Maya 80 artificial grass delivers the same plush, high-performance turf experience as its Revival counterpart, but with a polyurethane finish for added durability. Featuring W-shaped monofilament blades, a 1.57" pile height, and a 53oz face weight, it offers a soft yet resilient surface ideal for landscaping. The 4-tone green and beige blend mimics the look of natural grass, while the double polypropylene backing ensures lasting structure and strength. With a ≥35N tuft bind, high stitch rate, and 60L/m²/min drainage capacity, this model stands up to the elements while staying lush and dry. Maya 80 is a smart, low-maintenance choice backed by a 16-year warranty.

Specifications

Yarn Color:

4 Tones

Finishing Coating:

Polyurethane

Pile Height (inches:

1.57

Drainage Rate:

1.47 gal/ft²/min

Face Weight (Oz):

Application:

Residential and Commercial Landscape

Total Weight (Oz)

Warranty:

16 Years

Yarn Color:

4 Tones

Pile Height (In):

1.57

Face Weight (Oz):

Total Weight (Oz):

Finish Coating:

Polyurethane

Drainage Rate:

1.47 gal/ft²/min

Application:

Residential and Commercial Landscape

Warranty:

16 Years

Procedures

Artificial Grass Installation Procedure

Artificial Grass Installation

The following outlines our complete, industry-standard installation process, which fully rebuilds the foundation that was missing from the existing system and ensures proper drainage, stability, and longevity.
‍
Our installation begins by clearing the designated area of any existing grass, debris, and organic material.
‍
The surface is then graded for proper drainage and compacted to create a stable sub-base.
‍
A layer of crushed aggregate is installed and compacted — usually around 2–3 inches deep, depending on soil conditions and usage requirements. The base is mechanically compacted to approximately 90–95% density to prevent future settling and maintain a stable, even surface.

Once leveled, a commercial-grade weed barrier is laid over the compacted base to help prevent weed growth while allowing for drainage.

Next, the artificial grass is carefully rolled out and trimmed to fit the design. It is secured using 5" non-galvanized nails, placed approximately every 5 inches along the perimeter and every 12 inches within the interior of the turf. Seams are carefully joined to ensure durability and visual continuity.

Finally, the turf fibers are brushed upright and infilled with a material such as silica sand, antimicrobial, odor trapping, or cooling infill, depending on the application. This step enhances stability, appearance, and longevity. The area is then cleaned and groomed for a polished finish.

Decorative Rock Installation Procedure

Our decorative rock installations begin by carefully outlining the designated areas and removing any existing vegetation, debris, loose soil, or obstructions that could interfere with a stable installation. In many cases, this includes removing existing decorative rock, weeds, or organic material that has accumulated over time. The area is then lightly graded to create a smooth and even subgrade, eliminating low spots where water or debris might collect.

Once the surface is prepared, we install a commercial-grade 4oz woven weed barrier fabric designed to suppress weed growth while still allowing water to drain through the soil naturally. The fabric is overlapped at seams and securely pinned using landscape staples to prevent movement over time and to ensure continuous weed protection across the entire installation area.

Depending on the site conditions and the customer’s preference, we may install an optional graded and compacted base layer, typically consisting of Class II road base. When used, this base layer is usually installed at a depth of approximately 2–3 inches and compacted with vibratory plate compactors to create a firm, stable surface.

This optional base layer offers several advantages:

• Improves long-term stability of the decorative rock
• Reduces settling and migration of the rock into the soil
• Enhances drainage and prevents muddy conditions after rain
• Provides a smoother and more level finished surface

However, in many residential decorative rock installations—particularly where soil is already firm and well-draining—the base layer may be omitted to reduce cost and installation time. In these cases, the weed barrier fabric is installed directly over the prepared soil, and the decorative rock itself provides sufficient coverage and stability for the landscape application.

After the base preparation (if selected) and weed barrier installation are complete, the chosen decorative rock—such as river rock, crushed gravel, lava rock, or other decorative aggregates—is carefully distributed across the area at the specified depth. The material is evenly spread to achieve consistent coverage and proper thickness, typically ranging from 2 to 3 inches depending on the rock size and design requirements.

The surface is then final-raked and sculpted to create a clean, professional finish with smooth transitions and an even distribution of material. Special attention is given to shaping around trees, plants, irrigation components, and architectural features to maintain both functionality and visual appeal.

If required for the design, steel edging or bender board edging is installed along borders to contain the decorative rock and clearly define landscaped areas. Edging helps maintain crisp lines between rock, turf, concrete, or planting areas and prevents rock migration over time.

The result is a low-maintenance, visually appealing landscape surface that improves drainage, reduces weed growth, and enhances the overall curb appeal of the property.

Decomposed Granite (DG) Installation Procedure

Our decomposed granite installations start with clearing the designated area of grass, roots, and debris to establish a clean and stable foundation. Once the area is excavated and leveled, we install bender board or metal edging to contain the DG and create defined borders that prevent spreading over time.

A commercial-grade weed barrier fabric is laid down to inhibit weed growth while still allowing water to permeate through. This ensures a clean, low-maintenance finish over the long term.

We then apply a base layer of compacted Class II road base or crushed rock, typically around 2–3 inches deep, depending on site conditions and expected foot traffic. This base layer is leveled and compacted using a vibratory plate compactor to provide a stable sub-surface.

Next, we spread the decomposed granite evenly across the area in lifts of approximately 1.5 inches each. After each layer is spread, we lightly moisten the surface with water to aid in compaction and binding, then use the compactor again to press it into place. This process is repeated as needed until the final desired depth—usually around 2–3 inches total—is achieved.

We use stabilized DG upon request, which includes a binding agent to help the surface resist erosion and maintain a firmer finish under traffic. The final surface is lightly misted and compacted again for a smooth, walkable, and professional finish.

Paver Installation Procedure

Our paver installations begin with thorough site preparation, which includes marking the layout, removing any vegetation, and excavating the area to a depth that accommodates the paver thickness plus the required base layers—typically 7 to 9 inches total, depending on traffic load.

We then install edge restraints (such as bender board or concrete curbing) to maintain the integrity of the layout and prevent shifting over time.

A weed barrier fabric is laid down over the subgrade to reduce weed growth without impeding drainage.Next, we apply a compacted Class II road base or ¾” crushed aggregate in lifts of approximately 2–3 inches, compacting thoroughly after each lift using a vibratory plate compactor. This base layer is usually 4 to 6 inches thick, depending on whether the application is pedestrian or vehicular.

Over the compacted base, we spread a 1-inch bedding layer of washed concrete sand or similar material. This layer is carefully screeded to create a smooth, level surface that will support the pavers evenly.

Pavers are then laid by hand, following the desired pattern (e.g., herringbone, running bond, basketweave). We use spacers or consistent joints to allow for joint sand and proper interlocking.

Once all pavers are laid, we cut edge pieces as needed using a masonry saw or splitter to achieve a clean perimeter fit. After the entire surface is in place, we compact the pavers with a vibratory plate compactor fitted with a rubber pad to avoid surface damage.

We then apply polymeric sand or regular joint sand across the surface and sweep it into the joints. Polymeric sand is preferred for its binding and weed-prevention properties. The surface is compacted once more to help settle the sand.

Finally, for polymeric sand, we lightly mist the surface to activate the binding agent, resulting in a durable, low-maintenance, and visually appealing finish.

Stepping Stones Installation Procedure

The installation of stepping stones begins with careful planning and layout, ensuring proper spacing for comfortable walking. Typically, we maintain a distance of 18 to 24 inches (center to center) between stones to match the average human stride.

We begin by marking the path and then removing any grass or vegetation in each spot where a stone will be placed. Each area is excavated individually to a depth of approximately 2 to 4 inches, depending on the thickness of the stones and desired finish height.

Next, we install a weed barrier fabric under each stone location to help prevent weed growth while allowing drainage. A compacted base layer of decomposed granite (DG), sand, or crushed gravel is then added to each cavity, typically 1 to 2 inches thick, and compacted by hand to create a stable and level foundation.

Each stepping stone is then set into place manually, ensuring it sits level with the surrounding grade and is stable under foot pressure. We use a level and rubber mallet to adjust and secure each stone. The goal is a flush finish with just enough elevation to allow water runoff and avoid pooling.

If requested or aesthetically appropriate, we fill the joints between stones with decorative gravel, bark, DG, or artificial turf strips, depending on the overall landscaping theme and drainage requirements.

Once all stepping stones are in place and stable, we conduct a final inspection and make any necessary adjustments to ensure a safe, durable, and visually balanced pathway.

Concrete Installation Procedure

Our concrete installation process for residential patios, walkways, grill pads, and light-use driveways begins with site preparation and grading. We start by marking the layout, removing any vegetation, and excavating the area to a depth of approximately 4 to 6 inches, depending on the application and soil conditions.

A Class II road base or crushed gravel layer is then installed, typically 2 to 4 inches thick, and compacted thoroughly using a vibratory plate compactor. This creates a solid and stable foundation that prevents cracking and shifting over time.

Next, forms are constructed using high-quality lumber to define the edges and maintain consistent thickness and slope. We ensure that the concrete will drain away from any structures, avoiding pooling or water damage. If necessary, expansion joints or control joints are planned and marked to minimize cracking.

We then place concrete reinforcement, usually welded wire mesh or #3 rebar on chairs, based on project needs. This reinforcement adds tensile strength to help resist cracking and shifting.

A ready-mix concrete blend is then poured on-site, typically in the 3,000–3,500 psi range, which is ideal for residential use while allowing for ease of finishing. Our crew levels and floats the concrete, followed by edging and finishing the surface based on your selected texture—broom finish, smooth trowel, or decorative stamped finish.

Control joints are cut within 24 hours to prevent future cracking due to expansion and contraction.

After the surface has cured enough for final touch-ups, we apply curing compound (if requested) and rope off the area to protect it during the curing process. Light foot traffic is typically allowed after 24–48 hours, while vehicles should avoid driving on the slab for at least 7 days.

The result is a clean, durable concrete surface, ready to support daily use, outdoor furniture, BBQ grills, and more—adding both function and elegance to your outdoor space.

Hazard Mitigation Procedure

Not Included / Exclusions

This quote is limited to the combined backyard improvements specifically described in the Quote Summary. The following items are not included unless specifically added through a written change order:

Artificial turf, DG, gravel, pavers, irrigation, grading, or other landscaping in the existing natural-grass area located below the DG parking area. That area is intentionally excluded from the present scope.
Swimming-pool construction, repair, resurfacing, coping, tile, plumbing, electrical, pumps, filters, cleaning, pool-deck modification, or any other pool-system work.
Replacement, repair, leveling, sealing, resurfacing, or structural modification of existing concrete around the pool, covered patio, walkways, or other existing hardscape except for the specifically described new paver work.
New underground drainage systems, catch basins, French drains, dry wells, channel drains, sump systems, or drainage piping. The work will rely on practical grading and the property’s existing drainage conditions.
Correction of flooding, groundwater, neighboring runoff, inadequate downstream drainage, erosion originating outside the work area, or other pre-existing drainage deficiencies.
Structural fence repair, fence replacement, post replacement, footing repair, structural reinforcement, retaining-wall construction, or engineered erosion-control work. The included 2-inch by 12-inch pressure-treated board is a ground-level landscape finish/barrier only.
Structural engineering or load certification of the stabilized DG parking surface. TerraKoat EX and the compacted base are being installed as a residential landscape parking system, not as engineered pavement.
Repair of rutting, displacement, settlement, cracking, erosion, or wear caused by unsuitable subgrade, concentrated drainage, unusually heavy vehicles, trailers, equipment, aggressive tire turning, spinning tires, fluid leaks, or uses beyond normal residential parking.
Additional stabilized DG, road base, excavation, or remediation required because of concealed unstable soil, buried debris, undocumented fill, concrete, large rocks, roots, or other subsurface conditions not visible during the estimate.
Repair, relocation, or replacement of concealed irrigation, electrical, gas, plumbing, drainage, low-voltage wiring, pool lines, utility lines, or other underground systems encountered during excavation.
New irrigation systems, sprinkler relocation, valves, controllers, drip systems, planting irrigation, trees, shrubs, plants, mulch, or planting soil unless specifically described in the approved scope.
Additional pavers, stepping stones, decorative gravel, edging, or artificial turf outside the quantities and areas described in this proposal.
Built-up putting-green contours, shaped breaks, mounds, specialty golf-course construction, sand bunkers, chipping areas, golf-ball containment, lighting, training aids, or accessories beyond the two included cup/pole/flag sets.
Guarantee of professional golf-course or tournament-level putting speed, perfectly uniform ball roll, or identical performance in all temperatures, weather conditions, and maintenance states.
Repair or replacement of natural grass outside the project area beyond reasonable cleanup of the equipment access path. Equipment access may temporarily flatten or discolor existing lawn.
Moving or protecting customer furniture, grills, pool equipment, toys, decorations, planters, or personal property not already clear of the work areas before installation.
Damage caused by reflective window glare, concentrated sunlight, grills, hot equipment, fire pits, coals, cigarettes, fireworks, chemicals, petroleum products, sharp objects, vehicles on artificial turf, flooding, soil movement, rodents, wildlife, or work performed by others.
Permits, HOA approvals, architectural approvals, surveys, engineering, inspections, or governmental fees unless specifically required and added in writing.
Any additional work resulting from customer-requested layout changes, added square footage, material substitutions, concealed conditions, or work outside the approved concept. Such work requires customer authorization and may require revised pricing.

Notes:

Project Areas

DG parking area: approximately 300 square feet.
Regular Maya 80 turf area: approximately 460 square feet.
Putting-green zone: approximately 218 square feet, including approximately 105 square feet of dedicated putting surface and approximately 113 square feet of Maya 80 fringe.
Grill-area turf and paver zone: approximately 153 square feet.
Total Maya 80 landscape-turf coverage is approximately 724 square feet.
The existing natural-grass area beneath the DG parking section is not included in this project and will remain untouched.

Artificial Turf and Putting Green

Maya 80 is the selected landscape grass and will also form the fringe around the putting green.
The dedicated putting surface will use putting-green turf and will remain generally flat and simple, without built-up contours or intentionally shaped breaks.
Two complete cup, pole, and flag sets are included.
Final field cuts, seams, grain direction, fringe width, curves, and cup locations may be adjusted slightly to improve fit, appearance, playability, and material efficiency.
Maya 80 carries the applicable 16-year manufacturer warranty. The dedicated putting-green turf is subject to its applicable manufacturer warranty. Kreative Gardens provides a two-year workmanship warranty, subject to the written warranty terms, exclusions, proper use, and required maintenance.

DG Parking

The approximately 300-square-foot parking area will receive recycled Class II road base, mechanical compaction, approximately 2 to 2-1/2 inches of gray DG, and approximately 20 gallons of TerraKoat EX.
The stabilized surface is intended for normal residential parking. Turning tires while stationary, hard acceleration, braking, unusually heavy vehicles, concentrated runoff, and inadequate subgrade conditions can shorten the life of a stabilized aggregate surface.
Periodic maintenance or localized touch-up may eventually be required as with other stabilized aggregate surfaces.

Pavers, Gravel, Edging, and Fence

Nine new 24-inch by 24-inch pavers are included for the grill pad.
The rear paver layout will be modified to create the approved single-row extension using new pavers supplied by Kreative Gardens.
Designated white-rock areas will be replaced with 3/4-inch gray gravel to coordinate with the existing gray gravel already present in the yard.
Selected red edging brick will be replaced with black or gray concrete paver edging stones.
The right-side fence-bottom treatment will use brown-finished 2-inch by 12-inch pressure-treated lumber secured with approximately 18-inch steel stakes.

Package Pricing

Standard finance or credit-card price: $11,100.
Discounted cash price: $10,100. Financing is available for qualified customers.
Pricing assumes completion of the described work as one coordinated project. Individual line-item values are allocations within the package and do not represent guaranteed stand-alone prices or automatic deductions.
If any portion is removed or materially changed, the remaining scope must be repriced because mobilization, labor, equipment, delivery, disposal, base, and other project costs are shared across multiple areas.

Access and Site Conditions

Backyard access is generally good, but compact equipment may need to pass over or immediately adjacent to existing natural grass outside the gate.
Kreative Gardens will use reasonable temporary ground protection, but minor temporary lawn flattening or discoloration may occur from construction access.
All dimensions are approximate and subject to field verification before final installation.

The Fine Print

Before We Begin...

Please take a moment to review the details below. These notes cover important aspects of your project, such as warranties, material handling, and general terms. We believe in transparency and want you to feel confident every step of the way.

Mechanic’s Lien Warning

Mechanic's Lien Warning
Under California law, any contractor, subcontractor, laborer, supplier, or other person who helps improve your property but is not paid may record what is called a mechanic's lien on your property. A mechanic’s lien is a claim made against your property and may affect your ability to sell or refinance. This could happen even if you have paid your contractor in full.To protect yourself, you should request a Lien Release from all contractors and subcontractors after work is completed.

Change Order Clause

Change Orders
‍Any additions or modifications to the scope of work must be documented in a written change order, signed by both parties before additional work is performed. Change orders may result in additional charges and could impact the project timeline.

Cancellation Policy

Right to Cancel
‍You may cancel this agreement within three (3) business days of signing without penalty, as required by California state law. After this period, cancellations may be subject to forfeiture of any paid deposit, restocking fees, and/or costs incurred by the contractor up to the date of cancellation.

Payment Terms

Payments
‍A deposit is due upon approval of the quote. Balance is due upon project completion unless otherwise agreed in writing. Accepted payment methods include cash, check, Zelle, or debit/credit (fees may apply). Failure to remit final payment may result in collections or lien proceedings.

Delays or Access Issues

Project Delays or Access Restrictions
‍The client is responsible for ensuring access to the work area. Unforeseen delays due to weather, access, hidden utilities, or client-caused schedule changes may result in rescheduling and additional costs.

Pricing Validity

This quote is valid for 15 calendar days. After that, pricing may need to be adjusted to reflect current material or labor costs. We recommend confirming your project promptly to lock in this rate.

Legal Jurisdiction

Governing Law
‍This agreement shall be governed by and interpreted in accordance with the laws of the State of California. Any disputes shall be resolved in San Bernardino County, California.