Kreative Gardens LLC, License # 1137272

Project:

Backyard Marathon Artificial Turf

Prepared:

August 26, 2026

Quote Summary

This proposal is for the professional conversion of approximately 1,132 square feet of the backyard at 13344 Luna Rd., Victorville, CA into a clean, durable artificial lawn using Marathon artificial grass and CamoFill performance infill.

The principal installation area is a straightforward rectangular backyard section measuring approximately 56'10" long by 19'8" deep, together with the small approximately 7' × 2' rock area adjacent to the existing shed. The quoted 1,132-square-foot quantity reflects the complete approved turf footprint, including that small shed-side section.

Existing Rock Removal and Site Preparation

The approved turf area currently contains dirt and landscape rock. Kreative Gardens will remove the existing loose rock and unsuitable surface material within the approved turf footprint, excavate as needed to establish proper finished elevations, grade the area, install and mechanically compact an aggregate base, complete final surface preparation, install the artificial grass, seam where required, secure the perimeter, apply infill, power brush, and perform final cleanup.

The completed surface will be graded to follow practical existing elevations and drainage conditions. No new underground drainage system is included unless later added in writing.

Existing Shed and Future Shed Area

The existing shed will remain in place. The turf will be professionally cut and finished around the existing shed and the adjacent approved turf boundaries.

The layout also preserves the designated area beside the existing shed for a future second shed. Kreative Gardens is not supplying, assembling, anchoring, permitting, or installing the new shed under this proposal. The concept rendering is intended to illustrate the anticipated finished appearance after the turf installation and possible future placement of a second shed.

Marathon Artificial Grass

Jason selected Marathon after reviewing the available turf options. Marathon is a durable residential and commercial landscape turf with an approximately 1.57-inch pile height, 53-ounce face weight, approximately 82-ounce total weight, polyurethane finish coating, four-tone coloration, approximately 1.47 gal/ft²/min drainage, and a 16-year manufacturer warranty.

A more pet-specific turf option was discussed because two dogs will have access to the backyard. Jason nevertheless preferred Marathon because the area will also be used by children and family members and he preferred Marathon's overall appearance and feel. Marathon is suitable for residential landscape use, but because the dogs will use the yard for bathroom breaks, routine pet-turf cleaning and rinsing will remain important.

Pet- and Family-Conscious CamoFill Infill

Because the backyard will be used by children and two dogs, Kreative Gardens will use CamoFill performance infill rather than ordinary untreated silica sand. CamoFill provides ballast to help stabilize the turf, supports individual turf fibers, assists blade recovery after foot and pet traffic, and provides antimicrobial protection intended to help inhibit odor-causing bacteria, mold, and mildew.

CamoFill is especially appropriate for a residential lawn shared by family members and pets. It helps create a cleaner, better-performing turf system when combined with normal maintenance. Solid pet waste should be removed promptly, frequently used urination areas should be rinsed regularly, and a pet-safe enzymatic turf cleaner may be used according to its manufacturer instructions when needed. No turf or infill system is maintenance-free or guaranteed to permanently eliminate pet odors.

Existing Landscape Lights and Future Tree Openings

Three existing landscape-light locations were identified in the yard. Electrical troubleshooting, wiring repair, fixture repair, replacement, transformer work, and other electrical work are not included in this proposal.

If Kathleen or Jason would like to preserve those locations for future trees, Kreative Gardens can form simple turf openings/tree wells around the selected locations at no additional charge as part of this installation, provided the locations are confirmed before final turf cutting. The complimentary scope is limited to creating the turf opening and normal perimeter finish. Trees, soil amendments, irrigation, electrical repairs, planting, root barriers, and future maintenance are not included.

Project Pricing and Senior Discount

The regular credit-card or financing price for this complete approximately 1,132-square-foot artificial turf installation is $7,500.

Kathleen qualifies for a 10% senior-citizen discount, reducing the project from $7,500 to $6,750. An additional $150 cash-payment discount is available, resulting in a final $6,600 cash price when the senior discount and cash discount are combined.

Financing is available for qualified customers. The senior-citizen discount is already reflected in the stated $6,600 cash price and is not deducted again.

Grass Model Specifications

Selected Model

Marathon

Marathon 80 delivers a bold and structured appearance with its vibrant green tones and distinctive W-shaped monofilament blades, designed to mimic freshly mowed natural grass. Engineered for durability, this turf model features a 1.57" pile height and dense 17-stitch rate, supported by a strong double polypropylene backing and polyurethane finish coating. Its 4-tone color palette and beige thatch add depth and realism, while its robust 82oz total weight and >35N tuft bind ensure long-term performance. With a high drainage rate of 60L/m²/min and a 16-year warranty, Marathon 80 is ideal for residential and commercial landscapes demanding a natural look with heavy foot traffic resilience.

Specifications

Yarn Color:

4 tones

Finishing Coating:

Polyurethane

Pile Height (inches:

1.57

Drainage Rate:

1.47 gal/ft²/min

Face Weight (Oz):

Application:

Commercial and Residential Landscape

Total Weight (Oz)

Warranty:

16 years

Yarn Color:

4 tones

Pile Height (In):

1.57

Face Weight (Oz):

Total Weight (Oz):

Finish Coating:

Polyurethane

Drainage Rate:

1.47 gal/ft²/min

Application:

Commercial and Residential Landscape

Warranty:

16 years

Procedures

Artificial Grass Installation Procedure

Artificial Grass Installation

The following outlines our complete, industry-standard installation process, which fully rebuilds the foundation that was missing from the existing system and ensures proper drainage, stability, and longevity.
‍
Our installation begins by clearing the designated area of any existing grass, debris, and organic material.
‍
The surface is then graded for proper drainage and compacted to create a stable sub-base.
‍
A layer of crushed aggregate is installed and compacted — usually around 2–3 inches deep, depending on soil conditions and usage requirements. The base is mechanically compacted to approximately 90–95% density to prevent future settling and maintain a stable, even surface.

Once leveled, a commercial-grade weed barrier is laid over the compacted base to help prevent weed growth while allowing for drainage.

Next, the artificial grass is carefully rolled out and trimmed to fit the design. It is secured using 5" non-galvanized nails, placed approximately every 5 inches along the perimeter and every 12 inches within the interior of the turf. Seams are carefully joined to ensure durability and visual continuity.

Finally, the turf fibers are brushed upright and infilled with a material such as silica sand, antimicrobial, odor trapping, or cooling infill, depending on the application. This step enhances stability, appearance, and longevity. The area is then cleaned and groomed for a polished finish.

Decorative Rock Installation Procedure

Our decorative rock installations begin by carefully outlining the designated areas and removing any existing vegetation, debris, loose soil, or obstructions that could interfere with a stable installation. In many cases, this includes removing existing decorative rock, weeds, or organic material that has accumulated over time. The area is then lightly graded to create a smooth and even subgrade, eliminating low spots where water or debris might collect.

Once the surface is prepared, we install a commercial-grade 4oz woven weed barrier fabric designed to suppress weed growth while still allowing water to drain through the soil naturally. The fabric is overlapped at seams and securely pinned using landscape staples to prevent movement over time and to ensure continuous weed protection across the entire installation area.

Depending on the site conditions and the customer’s preference, we may install an optional graded and compacted base layer, typically consisting of Class II road base. When used, this base layer is usually installed at a depth of approximately 2–3 inches and compacted with vibratory plate compactors to create a firm, stable surface.

This optional base layer offers several advantages:

• Improves long-term stability of the decorative rock
• Reduces settling and migration of the rock into the soil
• Enhances drainage and prevents muddy conditions after rain
• Provides a smoother and more level finished surface

However, in many residential decorative rock installations—particularly where soil is already firm and well-draining—the base layer may be omitted to reduce cost and installation time. In these cases, the weed barrier fabric is installed directly over the prepared soil, and the decorative rock itself provides sufficient coverage and stability for the landscape application.

After the base preparation (if selected) and weed barrier installation are complete, the chosen decorative rock—such as river rock, crushed gravel, lava rock, or other decorative aggregates—is carefully distributed across the area at the specified depth. The material is evenly spread to achieve consistent coverage and proper thickness, typically ranging from 2 to 3 inches depending on the rock size and design requirements.

The surface is then final-raked and sculpted to create a clean, professional finish with smooth transitions and an even distribution of material. Special attention is given to shaping around trees, plants, irrigation components, and architectural features to maintain both functionality and visual appeal.

If required for the design, steel edging or bender board edging is installed along borders to contain the decorative rock and clearly define landscaped areas. Edging helps maintain crisp lines between rock, turf, concrete, or planting areas and prevents rock migration over time.

The result is a low-maintenance, visually appealing landscape surface that improves drainage, reduces weed growth, and enhances the overall curb appeal of the property.

Decomposed Granite (DG) Installation Procedure

Our decomposed granite installations start with clearing the designated area of grass, roots, and debris to establish a clean and stable foundation. Once the area is excavated and leveled, we install bender board or metal edging to contain the DG and create defined borders that prevent spreading over time.

A commercial-grade weed barrier fabric is laid down to inhibit weed growth while still allowing water to permeate through. This ensures a clean, low-maintenance finish over the long term.

We then apply a base layer of compacted Class II road base or crushed rock, typically around 2–3 inches deep, depending on site conditions and expected foot traffic. This base layer is leveled and compacted using a vibratory plate compactor to provide a stable sub-surface.

Next, we spread the decomposed granite evenly across the area in lifts of approximately 1.5 inches each. After each layer is spread, we lightly moisten the surface with water to aid in compaction and binding, then use the compactor again to press it into place. This process is repeated as needed until the final desired depth—usually around 2–3 inches total—is achieved.

We use stabilized DG upon request, which includes a binding agent to help the surface resist erosion and maintain a firmer finish under traffic. The final surface is lightly misted and compacted again for a smooth, walkable, and professional finish.

Paver Installation Procedure

Our paver installations begin with thorough site preparation, which includes marking the layout, removing any vegetation, and excavating the area to a depth that accommodates the paver thickness plus the required base layers—typically 7 to 9 inches total, depending on traffic load.

We then install edge restraints (such as bender board or concrete curbing) to maintain the integrity of the layout and prevent shifting over time.

A weed barrier fabric is laid down over the subgrade to reduce weed growth without impeding drainage.Next, we apply a compacted Class II road base or ¾” crushed aggregate in lifts of approximately 2–3 inches, compacting thoroughly after each lift using a vibratory plate compactor. This base layer is usually 4 to 6 inches thick, depending on whether the application is pedestrian or vehicular.

Over the compacted base, we spread a 1-inch bedding layer of washed concrete sand or similar material. This layer is carefully screeded to create a smooth, level surface that will support the pavers evenly.

Pavers are then laid by hand, following the desired pattern (e.g., herringbone, running bond, basketweave). We use spacers or consistent joints to allow for joint sand and proper interlocking.

Once all pavers are laid, we cut edge pieces as needed using a masonry saw or splitter to achieve a clean perimeter fit. After the entire surface is in place, we compact the pavers with a vibratory plate compactor fitted with a rubber pad to avoid surface damage.

We then apply polymeric sand or regular joint sand across the surface and sweep it into the joints. Polymeric sand is preferred for its binding and weed-prevention properties. The surface is compacted once more to help settle the sand.

Finally, for polymeric sand, we lightly mist the surface to activate the binding agent, resulting in a durable, low-maintenance, and visually appealing finish.

Stepping Stones Installation Procedure

The installation of stepping stones begins with careful planning and layout, ensuring proper spacing for comfortable walking. Typically, we maintain a distance of 18 to 24 inches (center to center) between stones to match the average human stride.

We begin by marking the path and then removing any grass or vegetation in each spot where a stone will be placed. Each area is excavated individually to a depth of approximately 2 to 4 inches, depending on the thickness of the stones and desired finish height.

Next, we install a weed barrier fabric under each stone location to help prevent weed growth while allowing drainage. A compacted base layer of decomposed granite (DG), sand, or crushed gravel is then added to each cavity, typically 1 to 2 inches thick, and compacted by hand to create a stable and level foundation.

Each stepping stone is then set into place manually, ensuring it sits level with the surrounding grade and is stable under foot pressure. We use a level and rubber mallet to adjust and secure each stone. The goal is a flush finish with just enough elevation to allow water runoff and avoid pooling.

If requested or aesthetically appropriate, we fill the joints between stones with decorative gravel, bark, DG, or artificial turf strips, depending on the overall landscaping theme and drainage requirements.

Once all stepping stones are in place and stable, we conduct a final inspection and make any necessary adjustments to ensure a safe, durable, and visually balanced pathway.

Concrete Installation Procedure

Our concrete installation process for residential patios, walkways, grill pads, and light-use driveways begins with site preparation and grading. We start by marking the layout, removing any vegetation, and excavating the area to a depth of approximately 4 to 6 inches, depending on the application and soil conditions.

A Class II road base or crushed gravel layer is then installed, typically 2 to 4 inches thick, and compacted thoroughly using a vibratory plate compactor. This creates a solid and stable foundation that prevents cracking and shifting over time.

Next, forms are constructed using high-quality lumber to define the edges and maintain consistent thickness and slope. We ensure that the concrete will drain away from any structures, avoiding pooling or water damage. If necessary, expansion joints or control joints are planned and marked to minimize cracking.

We then place concrete reinforcement, usually welded wire mesh or #3 rebar on chairs, based on project needs. This reinforcement adds tensile strength to help resist cracking and shifting.

A ready-mix concrete blend is then poured on-site, typically in the 3,000–3,500 psi range, which is ideal for residential use while allowing for ease of finishing. Our crew levels and floats the concrete, followed by edging and finishing the surface based on your selected texture—broom finish, smooth trowel, or decorative stamped finish.

Control joints are cut within 24 hours to prevent future cracking due to expansion and contraction.

After the surface has cured enough for final touch-ups, we apply curing compound (if requested) and rope off the area to protect it during the curing process. Light foot traffic is typically allowed after 24–48 hours, while vehicles should avoid driving on the slab for at least 7 days.

The result is a clean, durable concrete surface, ready to support daily use, outdoor furniture, BBQ grills, and more—adding both function and elegance to your outdoor space.

Hazard Mitigation Procedure

Not Included / Exclusions

This quote is limited to the approximately 1,132-square-foot backyard artificial turf installation described in the Quote Summary. The following items are not included unless specifically added through a written change order:

Electrical troubleshooting, electrical repair, fixture replacement, transformer work, low-voltage wiring, rewiring, conduit, switches, controls, or restoration of the three existing landscape lights.
Supply, planting, delivery, staking, irrigation, fertilization, soil amendment, root barriers, or ongoing care for any future trees. If requested before final turf cutting, simple turf openings/tree wells at the selected existing light locations are included at no additional charge.
Supply, assembly, anchoring, foundation construction, permitting, installation, relocation, or modification of the future second shed.
Repair, relocation, leveling, structural modification, or replacement of the existing shed.
Swimming-pool repair, liner replacement, leveling, filling, cleaning, plumbing, pumps, filtration, electrical work, structural repair, or any other pool-related work. Any pool appearance shown in concept imagery is illustrative only.
Installation of new drains, catch basins, French drains, dry wells, channel drains, sump systems, or underground drainage piping.
Correction of flooding, groundwater, neighboring runoff, inadequate downstream drainage, or other pre-existing drainage conditions outside normal turf grading.
New irrigation systems, drip irrigation, sprinkler heads, valves, controllers, or significant irrigation rerouting.
Repair or relocation of concealed irrigation, electrical, gas, plumbing, drainage, low-voltage wiring, utility lines, or other underground systems not visible during the estimate.
Major engineered grading, retaining walls, soil stabilization, compaction testing, geotechnical services, or remediation of unstable, expansive, contaminated, rocky, or otherwise unsuitable soil.
Removal of buried concrete, large rocks, undocumented construction debris, buried stumps, extensive root systems, or other significant concealed subsurface obstructions requiring substantial additional labor or equipment.
Repair, replacement, resurfacing, leveling, sealing, or structural modification of existing concrete, patio structures, walls, fences, gates, house improvements, or neighboring property.
Complete or permanent elimination of pet odors. CamoFill assists with odor management but requires prompt waste removal, routine rinsing, cleaning, and normal maintenance.
Damage caused by pets digging, chewing, scratching, pulling, or otherwise damaging turf, seams, edges, infill, base, or fastening systems.
Damage caused by reflective window glare, concentrated sunlight, grills, fire pits, hot objects, chemicals, sharp objects, vehicles, flooding, soil movement, future tree-root growth, rodents, wildlife, or work performed by others.
Permits, HOA or architectural approvals, surveys, engineering, inspections, or governmental fees unless specifically required and added in writing.
Additional square footage, customer-requested layout changes, or additional labor/material required because of concealed or unforeseen site conditions. Such work requires customer approval before proceeding.

Notes:

Project Area and Layout

Estimated artificial turf coverage is approximately 1,132 square feet.
The principal yard area measures approximately 56'10" × 19'8".
The total includes the small approximately 7' × 2' rock section adjacent to the existing shed.
The existing shed remains. The designated space beside it is being preserved for a possible future second shed.
All dimensions are approximate and subject to normal field verification before final cutting and installation.

Marathon and Pet Use

Marathon is the customer-selected turf.
A pet-specific turf option was discussed because the household dogs will use the backyard for bathroom breaks. Jason selected Marathon based on his preference for the turf's appearance and family-use characteristics.
Marathon carries the applicable 16-year manufacturer warranty. Kreative Gardens provides a two-year workmanship warranty, subject to the written warranty terms, exclusions, proper use, and required maintenance.
Artificial grass has a directional grain. Fiber direction, seam location, sunlight, viewing angle, and surrounding shade may create normal differences in appearance or sheen.

CamoFill

CamoFill performance infill is included because children and pets are expected to use the lawn.
CamoFill adds ballast, supports the turf fibers, assists blade recovery, and provides antimicrobial protection intended to help inhibit odor-causing bacteria, mold, and mildew.
Solid pet waste should be removed promptly. Frequently used urination areas should be rinsed regularly, particularly during warm and dry weather.
No artificial turf or infill system is maintenance-free or guaranteed to eliminate all pet odors.

Lights and Future Trees

Electrical work for the three existing landscape lights is excluded.
If tree locations are confirmed before final turf cutting, Kreative Gardens may create simple turf openings/tree wells at those locations at no additional installation charge.
Trees, planting, irrigation, soil amendments, electrical work, and root barriers remain excluded.

Pricing

Regular credit-card or financing price: $7,500.
10% senior-citizen discount: -$750, producing an adjusted price of $6,750.
Additional cash-payment discount: -$150.
Final cash price with senior discount already applied: $6,600.
The senior discount is already included in the $6,600 cash price and should not be applied a second time.

The Fine Print

Before We Begin...

Please take a moment to review the details below. These notes cover important aspects of your project, such as warranties, material handling, and general terms. We believe in transparency and want you to feel confident every step of the way.

Mechanic’s Lien Warning

Mechanic's Lien Warning
Under California law, any contractor, subcontractor, laborer, supplier, or other person who helps improve your property but is not paid may record what is called a mechanic's lien on your property. A mechanic’s lien is a claim made against your property and may affect your ability to sell or refinance. This could happen even if you have paid your contractor in full.To protect yourself, you should request a Lien Release from all contractors and subcontractors after work is completed.

Change Order Clause

Change Orders
‍Any additions or modifications to the scope of work must be documented in a written change order, signed by both parties before additional work is performed. Change orders may result in additional charges and could impact the project timeline.

Cancellation Policy

Right to Cancel
‍You may cancel this agreement within three (3) business days of signing without penalty, as required by California state law. After this period, cancellations may be subject to forfeiture of any paid deposit, restocking fees, and/or costs incurred by the contractor up to the date of cancellation.

Payment Terms

Payments
‍A deposit is due upon approval of the quote. Balance is due upon project completion unless otherwise agreed in writing. Accepted payment methods include cash, check, Zelle, or debit/credit (fees may apply). Failure to remit final payment may result in collections or lien proceedings.

Delays or Access Issues

Project Delays or Access Restrictions
‍The client is responsible for ensuring access to the work area. Unforeseen delays due to weather, access, hidden utilities, or client-caused schedule changes may result in rescheduling and additional costs.

Pricing Validity

This quote is valid for 15 calendar days. After that, pricing may need to be adjusted to reflect current material or labor costs. We recommend confirming your project promptly to lock in this rate.

Legal Jurisdiction

Governing Law
‍This agreement shall be governed by and interpreted in accordance with the laws of the State of California. Any disputes shall be resolved in San Bernardino County, California.