Kreative Gardens LLC, License # 1137272

Project:

Apple Valley Front Yard Turf, Arizona Cobble & Decorative Seat Wall

Prepared:

October 2, 2026

Quote Summary

This proposal covers the complete front-yard landscape renovation at 10860 Aster Ln, Apple Valley, CA 92308. The existing front yard contains approximately 1,675 sq. ft. of natural grass. The final design will combine approximately 785 sq. ft. of Marathon premium artificial turf, approximately 890 sq. ft. of Arizona cobble or comparable premium decorative cobble, a custom curved decorative seating wall around the existing tree, and installation of up to ten owner-supplied plants.

Existing Lawn Removal and Site Preparation

Kreative Gardens will remove the existing natural grass throughout the approved project footprint, excavate as required to establish proper finished elevations, and haul away normal demolition debris generated by the project. We recommend suspending lawn irrigation approximately 4–5 days before demolition, when HOA requirements and weather permit, so the upper soil profile can partially dry.

Marathon Premium Artificial Turf — Approx. 785 sq. ft.

The approved turf areas will be installed with Marathon premium artificial grass. Preparation includes commercial-grade weed-barrier fabric, approximately 2.5–3 inches of recycled Class II road base where required, grading, moisture conditioning as needed, and mechanical compaction.

The turf will be professionally laid with consistent fiber direction, cut and fitted around permanent features, seamed where required, securely fastened, infilled, power brushed, and cleaned. Composite bender board will be used where required to create clean transitions between turf and decorative-rock areas.

Along the neighboring property boundaries, 2×4 pressure-treated ground-contact lumber will be used where required as a durable concealed turf termination and fastening edge.

Arizona Cobble Decorative Rock — Approx. 890 sq. ft.

The decorative landscape areas will be finished with Arizona cobble or comparable premium decorative cobble at an approximate nominal depth of 2–3 inches, installed over commercial-grade landscape fabric/geotextile.

The entire lawn area to the left of the driveway will be converted to decorative rock. On the right side of the front yard, the turf areas will terminate approximately 3 feet before the public sidewalk; those sidewalk-adjacent bands will be finished with matching decorative rock and planting areas.

Alternative Decorative Rock — Deduct $300: If the homeowners prefer a standard 1–3 inch decorative rock instead of Arizona cobble or comparable premium cobble, $300 will be deducted from the quoted project price. The final color and material will be selected by the homeowners and confirmed before materials are ordered.

‍

Custom Curved Decorative Seating Wall

Kreative Gardens will construct a custom curved decorative seat wall in front of the existing mature tree. The wall is planned as an approximately 12-foot-diameter semicircular layout, approximately 19 linear feet along the curved face, and approximately 20 inches finished height.

The wall will be constructed with Pavestone-style beige concrete retaining-wall blocks similar to the selected 4 in. × 11.75 in. × 6.75 in. block. It will consist of approximately six courses, with the first course partially embedded and carefully leveled over the prepared compacted foundation. Courses will have staggered joints and exterior landscape-block adhesive between courses.

The top will be finished with coordinating concrete cap blocks, fully adhered to provide a smoother seating surface. The wall is intended as a decorative seating wall, not as an engineered structural retaining wall. Existing tree trunk and root-flare elevations will not intentionally be raised or buried.

Owner-Supplied Plant Installation

The proposal includes installation of up to ten (10) owner-supplied plants, maximum 5-gallon container size each. Plants may be available at the job site or picked up locally by Kreative Gardens by prior arrangement. Plant purchase cost is not included.

Irrigation, Drainage and Utilities

Existing irrigation serving areas converted to artificial turf or decorative rock will be capped or terminated at practical locations. Existing general drainage patterns will be maintained; major drainage-system modifications are not included unless specifically added in writing. Existing utility boxes, cleanouts, valve boxes, and similar service points will remain accessible and incorporated into the finished grade.

HOA Design Assistance

Kreative Gardens will prepare a conceptual landscape sketch for HOA review showing the proposed turf, decorative-rock areas, planting zones, borders, and decorative seat wall. Available material samples and specifications will also be provided for the homeowner's architectural submission. HOA approval remains the homeowner's responsibility, and HOA-required changes that materially alter the scope may require a revised proposal.

Project Pricing

The complete Arizona-cobble landscape package is $14,000 when paid by credit card or through approved financing. A discounted $13,300 cash price is available.

DG Alternative: If decomposed granite is selected in place of the decorative-rock areas, the discounted cash price is $12,500.

Owner Haul-Away Option — Deduct $500: Kreative Gardens will cut, remove, and stage the existing sod/material in an accessible area. The homeowner will be responsible for loading, hauling, and legally disposing of all staged sod and associated soil. Staged material must be removed promptly and may not interfere with installation access or the project schedule.

Kreative Gardens provides its standard two-year workmanship warranty. Marathon carries the applicable 16-year manufacturer warranty, subject to the manufacturer's written terms and exclusions.

Grass Model Specifications

Selected Model

Marathon

Marathon 80 delivers a bold and structured appearance with its vibrant green tones and distinctive W-shaped monofilament blades, designed to mimic freshly mowed natural grass. Engineered for durability, this turf model features a 1.57" pile height and dense 17-stitch rate, supported by a strong double polypropylene backing and polyurethane finish coating. Its 4-tone color palette and beige thatch add depth and realism, while its robust 82oz total weight and >35N tuft bind ensure long-term performance. With a high drainage rate of 60L/m²/min and a 16-year warranty, Marathon 80 is ideal for residential and commercial landscapes demanding a natural look with heavy foot traffic resilience.

Specifications

Yarn Color:

4 tones

Finishing Coating:

Polyurethane

Pile Height (inches:

1.57

Drainage Rate:

1.47 gal/ft²/min

Face Weight (Oz):

Application:

Commercial and Residential Landscape

Total Weight (Oz)

Warranty:

16 years

Yarn Color:

4 tones

Pile Height (In):

1.57

Face Weight (Oz):

Total Weight (Oz):

Finish Coating:

Polyurethane

Drainage Rate:

1.47 gal/ft²/min

Application:

Commercial and Residential Landscape

Warranty:

16 years

Procedures

Artificial Grass Installation Procedure

Artificial Grass Installation

The following outlines our complete, industry-standard installation process, which fully rebuilds the foundation that was missing from the existing system and ensures proper drainage, stability, and longevity.
‍
Our installation begins by clearing the designated area of any existing grass, debris, and organic material.
‍
The surface is then graded for proper drainage and compacted to create a stable sub-base.
‍
A layer of crushed aggregate is installed and compacted — usually around 2–3 inches deep, depending on soil conditions and usage requirements. The base is mechanically compacted to approximately 90–95% density to prevent future settling and maintain a stable, even surface.

Once leveled, a commercial-grade weed barrier is laid over the compacted base to help prevent weed growth while allowing for drainage.

Next, the artificial grass is carefully rolled out and trimmed to fit the design. It is secured using 5" non-galvanized nails, placed approximately every 5 inches along the perimeter and every 24 inches within the interior of the turf. Seams are carefully joined to ensure durability and visual continuity.

Finally, the turf fibers are brushed upright and infilled with a material such as silica sand, antimicrobial, odor trapping, or cooling infill, depending on the application. This step enhances stability, appearance, and longevity. The area is then cleaned and groomed for a polished finish.

Decorative Rock Installation Procedure

Our decorative rock installations begin by carefully outlining the designated areas and removing any existing vegetation, debris, loose soil, or obstructions that could interfere with a stable installation. In many cases, this includes removing existing decorative rock, weeds, or organic material that has accumulated over time. The area is then lightly graded to create a smooth and even subgrade, eliminating low spots where water or debris might collect.

Once the surface is prepared, we install a commercial-grade 4oz woven weed barrier fabric designed to suppress weed growth while still allowing water to drain through the soil naturally. The fabric is overlapped at seams and securely pinned using landscape staples to prevent movement over time and to ensure continuous weed protection across the entire installation area.

Depending on the site conditions and the customer’s preference, we may install an optional graded and compacted base layer, typically consisting of Class II road base. When used, this base layer is usually installed at a depth of approximately 2–3 inches and compacted with vibratory plate compactors to create a firm, stable surface.

This optional base layer offers several advantages:

• Improves long-term stability of the decorative rock
• Reduces settling and migration of the rock into the soil
• Enhances drainage and prevents muddy conditions after rain
• Provides a smoother and more level finished surface

However, in many residential decorative rock installations—particularly where soil is already firm and well-draining—the base layer may be omitted to reduce cost and installation time. In these cases, the weed barrier fabric is installed directly over the prepared soil, and the decorative rock itself provides sufficient coverage and stability for the landscape application.

After the base preparation (if selected) and weed barrier installation are complete, the chosen decorative rock—such as river rock, crushed gravel, lava rock, or other decorative aggregates—is carefully distributed across the area at the specified depth. The material is evenly spread to achieve consistent coverage and proper thickness, typically ranging from 2 to 3 inches depending on the rock size and design requirements.

The surface is then final-raked and sculpted to create a clean, professional finish with smooth transitions and an even distribution of material. Special attention is given to shaping around trees, plants, irrigation components, and architectural features to maintain both functionality and visual appeal.

If required for the design, steel edging or bender board edging is installed along borders to contain the decorative rock and clearly define landscaped areas. Edging helps maintain crisp lines between rock, turf, concrete, or planting areas and prevents rock migration over time.

The result is a low-maintenance, visually appealing landscape surface that improves drainage, reduces weed growth, and enhances the overall curb appeal of the property.

Decomposed Granite (DG) Installation Procedure

Our decomposed granite installations start with clearing the designated area of grass, roots, and debris to establish a clean and stable foundation. Once the area is excavated and leveled, we install bender board or metal edging to contain the DG and create defined borders that prevent spreading over time.

A commercial-grade weed barrier fabric is laid down to inhibit weed growth while still allowing water to permeate through. This ensures a clean, low-maintenance finish over the long term.

We then apply a base layer of compacted Class II road base or crushed rock, typically around 2–3 inches deep, depending on site conditions and expected foot traffic. This base layer is leveled and compacted using a vibratory plate compactor to provide a stable sub-surface.

Next, we spread the decomposed granite evenly across the area in lifts of approximately 1.5 inches each. After each layer is spread, we lightly moisten the surface with water to aid in compaction and binding, then use the compactor again to press it into place. This process is repeated as needed until the final desired depth—usually around 2–3 inches total—is achieved.

We use stabilized DG upon request, which includes a binding agent to help the surface resist erosion and maintain a firmer finish under traffic. The final surface is lightly misted and compacted again for a smooth, walkable, and professional finish.

Paver Installation Procedure

Our paver installations begin with thorough site preparation, which includes marking the layout, removing any vegetation, and excavating the area to a depth that accommodates the paver thickness plus the required base layers—typically 7 to 9 inches total, depending on traffic load.

We then install edge restraints (such as bender board or concrete curbing) to maintain the integrity of the layout and prevent shifting over time.

A weed barrier fabric is laid down over the subgrade to reduce weed growth without impeding drainage.Next, we apply a compacted Class II road base or ¾” crushed aggregate in lifts of approximately 2–3 inches, compacting thoroughly after each lift using a vibratory plate compactor. This base layer is usually 4 to 6 inches thick, depending on whether the application is pedestrian or vehicular.

Over the compacted base, we spread a 1-inch bedding layer of washed concrete sand or similar material. This layer is carefully screeded to create a smooth, level surface that will support the pavers evenly.

Pavers are then laid by hand, following the desired pattern (e.g., herringbone, running bond, basketweave). We use spacers or consistent joints to allow for joint sand and proper interlocking.

Once all pavers are laid, we cut edge pieces as needed using a masonry saw or splitter to achieve a clean perimeter fit. After the entire surface is in place, we compact the pavers with a vibratory plate compactor fitted with a rubber pad to avoid surface damage.

We then apply polymeric sand or regular joint sand across the surface and sweep it into the joints. Polymeric sand is preferred for its binding and weed-prevention properties. The surface is compacted once more to help settle the sand.

Finally, for polymeric sand, we lightly mist the surface to activate the binding agent, resulting in a durable, low-maintenance, and visually appealing finish.

Stepping Stones Installation Procedure

The installation of stepping stones begins with careful planning and layout, ensuring proper spacing for comfortable walking. Typically, we maintain a distance of 18 to 24 inches (center to center) between stones to match the average human stride.

We begin by marking the path and then removing any grass or vegetation in each spot where a stone will be placed. Each area is excavated individually to a depth of approximately 2 to 4 inches, depending on the thickness of the stones and desired finish height.

Next, we install a weed barrier fabric under each stone location to help prevent weed growth while allowing drainage. A compacted base layer of decomposed granite (DG), sand, or crushed gravel is then added to each cavity, typically 1 to 2 inches thick, and compacted by hand to create a stable and level foundation.

Each stepping stone is then set into place manually, ensuring it sits level with the surrounding grade and is stable under foot pressure. We use a level and rubber mallet to adjust and secure each stone. The goal is a flush finish with just enough elevation to allow water runoff and avoid pooling.

If requested or aesthetically appropriate, we fill the joints between stones with decorative gravel, bark, DG, or artificial turf strips, depending on the overall landscaping theme and drainage requirements.

Once all stepping stones are in place and stable, we conduct a final inspection and make any necessary adjustments to ensure a safe, durable, and visually balanced pathway.

Concrete Installation Procedure

Our concrete installation process for residential patios, walkways, grill pads, and light-use driveways begins with site preparation and grading. We start by marking the layout, removing any vegetation, and excavating the area to a depth of approximately 4 to 6 inches, depending on the application and soil conditions.

A Class II road base or crushed gravel layer is then installed, typically 2 to 4 inches thick, and compacted thoroughly using a vibratory plate compactor. This creates a solid and stable foundation that prevents cracking and shifting over time.

Next, forms are constructed using high-quality lumber to define the edges and maintain consistent thickness and slope. We ensure that the concrete will drain away from any structures, avoiding pooling or water damage. If necessary, expansion joints or control joints are planned and marked to minimize cracking.

We then place concrete reinforcement, usually welded wire mesh or #3 rebar on chairs, based on project needs. This reinforcement adds tensile strength to help resist cracking and shifting.

A ready-mix concrete blend is then poured on-site, typically in the 3,000–3,500 psi range, which is ideal for residential use while allowing for ease of finishing. Our crew levels and floats the concrete, followed by edging and finishing the surface based on your selected texture—broom finish, smooth trowel, or decorative stamped finish.

Control joints are cut within 24 hours to prevent future cracking due to expansion and contraction.

After the surface has cured enough for final touch-ups, we apply curing compound (if requested) and rope off the area to protect it during the curing process. Light foot traffic is typically allowed after 24–48 hours, while vehicles should avoid driving on the slab for at least 7 days.

The result is a clean, durable concrete surface, ready to support daily use, outdoor furniture, BBQ grills, and more—adding both function and elegance to your outdoor space.

Hazard Mitigation Procedure

Not Included / Exclusions

This proposal is limited to the work specifically described in the Quote Summary and approved project layout. Unless specifically added by written change order, the following are not included:

Plant purchase cost, plants larger than 5-gallon size, trees, large palms, soil amendments, or installation of more than ten owner-supplied plants.
Major irrigation redesign, new valves/controllers, or irrigation systems serving areas outside the approved footprint.
Major drainage-system modification, engineered drainage correction, catch basins, French drains, dry wells, sump systems, or new underground drainage piping.
Structural retaining walls, engineering, geotechnical investigation, compaction testing, soils testing, surveys, or correction of pre-existing soil instability.
Repair or relocation of concealed electrical, gas, water, sewer, drainage, low-voltage wiring, unidentified irrigation mains, buried concrete, foundations, large rocks, construction debris, or other concealed obstructions.
Repair or modification of the driveway, public sidewalk, walkway, house, fencing, neighboring improvements, or other retained hardscape.
Major tree-root cutting, arborist services, root barriers, guarantees regarding tree health, or changes to the existing tree's root-flare elevation.
Permanent prevention of weeds in decorative-rock areas.
HOA fees, governmental permits, engineering, inspections, or third-party professional fees. Final HOA approval is the homeowner's responsibility.
Additional square footage, customer-requested layout changes, or added labor/material due to concealed or unforeseen site conditions.

Notes:

Project Summary

Existing natural-grass footprint: approximately 1,675 sq. ft..
Marathon artificial turf: approximately 785 sq. ft..
Arizona cobble / premium decorative cobble: approximately 890 sq. ft., nominal 2–3 in. depth over landscape fabric.
Three-foot decorative-rock bands along the sidewalk in the approved right-side areas; full existing lawn area left of the driveway converts to decorative rock.
Composite bender board between turf and rock transitions where required.
2×4 pressure-treated ground-contact lumber at neighboring property boundaries where required.
Existing irrigation within converted areas capped/terminated as required.
Installation of up to ten owner-supplied plants, maximum 5-gallon size.
Decorative seat wall: approx. 12-ft-diameter semicircle, approx. 19 LF curved face, approx. 20 in. finished height, six courses, adhesive between courses, coordinating adhered cap blocks.

Pricing

Standard / credit card / approved financing price with Arizona cobble: $14,000.
Discounted cash price with Arizona cobble: $13,300.
DG alternative cash price: $12,500.
Owner haul-away option: deduct $500.

The Fine Print

Before We Begin...

Please take a moment to review the details below. These notes cover important aspects of your project, such as warranties, material handling, and general terms. We believe in transparency and want you to feel confident every step of the way.

Mechanic’s Lien Warning

Mechanic's Lien Warning
Under California law, any contractor, subcontractor, laborer, supplier, or other person who helps improve your property but is not paid may record what is called a mechanic's lien on your property. A mechanic’s lien is a claim made against your property and may affect your ability to sell or refinance. This could happen even if you have paid your contractor in full.To protect yourself, you should request a Lien Release from all contractors and subcontractors after work is completed.

Change Order Clause

Change Orders
‍Any additions or modifications to the scope of work must be documented in a written change order, signed by both parties before additional work is performed. Change orders may result in additional charges and could impact the project timeline.

Cancellation Policy

Right to Cancel
‍You may cancel this agreement within three (3) business days of signing without penalty, as required by California state law. After this period, cancellations may be subject to forfeiture of any paid deposit, restocking fees, and/or costs incurred by the contractor up to the date of cancellation.

Payment Terms

Payments
‍A deposit is due upon approval of the quote. Balance is due upon project completion unless otherwise agreed in writing. Accepted payment methods include cash, check, Zelle, or debit/credit (fees may apply). Failure to remit final payment may result in collections or lien proceedings.

Delays or Access Issues

Project Delays or Access Restrictions
‍The client is responsible for ensuring access to the work area. Unforeseen delays due to weather, access, hidden utilities, or client-caused schedule changes may result in rescheduling and additional costs.

Pricing Validity

This quote is valid for 15 calendar days. After that, pricing may need to be adjusted to reflect current material or labor costs. We recommend confirming your project promptly to lock in this rate.

Legal Jurisdiction

Governing Law
‍This agreement shall be governed by and interpreted in accordance with the laws of the State of California. Any disputes shall be resolved in San Bernardino County, California.